Skip to content

The machine

No-go zones

Mark clamps and the vise as zones with a height: Dusty checks the whole toolpath, jogs and macros against them, and blocks what it cannot check.

A no-go zone marks what the tool must not touch: a clamp placed for this project, or the vise fixed on the table. It has a height: the tool may pass above it, never through it. Zones never produce G-code: they are only used for checking.

  • Project zones (orange, stock coordinates), saved in the .dusty file: clamps.
  • Machine zones (red, machine coordinates), saved in the machine profile: the vise, a fixed jig. They apply to every project, and require homing.

Drawing

Machine panel › No-Go Zones…, or the button of the same name below the machine in Studio. Choose Project or Machine, Rectangle or Circle, then drag with the mouse or a finger on the plan. From Selection takes a closed shape from the drawing; Add by Numbers creates a zone to complete. Touching a zone selects it: its fields give the position, the size, the margin (1 mm by default) and the height; the plan shows it hatched, with the position of the tool. Use Current Tool Position locates a machine zone without measuring. Delete asks for confirmation.

The height works as follows, and this is the point to check before relying on it:

  • The check looks at the tip of the tool, in work coordinates: those of the G-code, positive Z upward, 0 where the tool set its Z zero. The tool flies over a zone if its tip stays at least at height + margin.
  • Project zone: the height is counted from the stock top. 20 means “the clamp rises 20 mm above the stock top”; it is negative if the clamp stays lower. Dusty works out the work Z from it, whatever the Z zero of the project: with Z0 on the top, work Z 20; with Z0 on the spoilboard and an 18 mm stock, work Z 38. This assumes the machine’s Z zero really was set the way the project says.
  • Machine zone: the height is a work Z, to confirm for the Z zero in force (Use Tool Height or Confirm for Current Zero). Dusty keeps that zero: if it changes (another stock, another tool), no flying over is allowed and crossing becomes uncheckable, until the next confirmation.
  • Without a height, the zone blocks at every Z, even at the top of travel.
  • After a tool change (M6), the check assumes the Z zero was set again, as the prompt asks. It does not know the real length of the tool. A G53 in Z does not say where the tip is: until a work Z follows, flying over is not allowed.

The check looks at the whole path, not at end points: G0, G1, arcs and helixes, taking G53, G54–G59, G92, G90/G91 and G20/G21 into account. The zone is enlarged by the tool radius and the margin. For an imported G-code, whose tool is unknown, Dusty assumes a 6 mm radius and says so: a wider tool needs a larger margin. It applies to the pre-send check, the start, framing and the dry run, manual moves (a continuous jog stops before the zone), Go To, saved positions, macros, the console, resume and jobs submitted to Dusty Link. Raising Z without moving in XY is always allowed, to clear the tool.

Three answers, never a fourth:

  • Whole path checked: no active zone is crossed, nothing blocks. With no active zone, Dusty says nothing: that is not an “OK”.
  • No-go zone: the start or the move is refused. The message says which zone, of which family, at which line or operation, where, at what height, and how to fix it.
  • Cannot be checked: Dusty cannot answer, and this blocks too. Causes: no homing (machine zones), unreadable position or offset, work zero not set since connecting, position lost, height not confirmed, tool length unknown after a change, line not understood (macros, variables, O, M98, rotary axes, unknown codes), unknown path (G28, G30, cycles, M6 left to the controller), file on the SD card.

Turning a zone off (Zone active box) is the only way past it: there is no override. A zone that is off is still shown as such, gray on the plan and in the Machine panel; each job started without it notes it in the machining log (zones_coupees column of the export). Starting stays an explicit action.

Limits

These checks rest on what you drew and on the zeros you set. They do not see the real table: always verify with framing and a dry run, and keep your hand near the stop. The 3D view does not show zones (they show on the work plane and in their window). Homing itself is not checked: the machine must be able to do it without hitting anything. An imported G-code is only checked when connected to a machine: only the driver knows the coordinates. A machine without homing ($22=0) cannot use machine zones: make them project zones. Shared machine: only the zones in the Dusty Link profile count. Headless, send it the profile from Dusty Studio (Dusty Link section); in Hub mode, draw them on the computer that shares the machine. Project zones go with the job.

This manual is also built into Dusty: press F1, or open the Help menu, to read the topic for what you are doing. A mistake, a missing answer? Tell us

Try it in Dusty, for free.

Free CNC milling software: design, toolpaths and machine control. Mac, iPad, iPhone, Windows and Linux.