Skip to content

Dusty Link: the shared CNC

Plug the CNC into a Raspberry Pi, an old PC or the desktop app in Hub mode: the iPad, the iPhone, the Mac and every browser of the workshop drive it over the local network — and your phone becomes a pendant.

How it works

Three steps, then the machine is shared.

  1. Install Dusty Link next to the CNC. A single line on a Raspberry Pi or a Linux PC, a folder to unzip on Windows — or the Hub mode of the desktop app, which keeps the machine on its own screen.
  2. Join from your devices. The Dusty apps find it on the network; enter the 8-character pairing code once. A browser opens its address and gets Dusty Studio, served by Dusty Link itself.
  3. Send, confirm, machine. Each job waits in the queue and starts only after a confirmation on the device that sends it. Pause, tool change and STOP stay available from every device.

What it changes in the workshop

The iPad drives a USB CNC

The iPad has no serial port: through Dusty Link, it drives any USB machine like the Mac does.

Your phone becomes a pendant

Jog, zero, probe Z, start, pause and STOP from the phone next to the machine, with nothing to install: scan the QR code and it opens already paired.

Dusty Studio for every browser

Dusty Link serves Dusty Studio to the computers and tablets of the workshop network: nothing to install on them either.

The same safeguards

Control goes through the same core as a direct connection: same pre-flight check, same incident cards, same tool change prompt, same STOP.

Scripts welcome

The dusty command, installed with Dusty Link, checks, estimates and sends a project from a terminal or a script — starting it still asks for an explicit confirmation.

Local network only

Dusty Link only accepts local network addresses: it is never reachable from the Internet, and nothing goes through our servers.

Which computer next to the CNC?

A few megabytes of memory are enough: the computer that sleeps in a drawer will do.

Raspberry Pi

Every model, from the Pi 1 and Zero to the Pi 5, on a 32- or 64-bit system.

Other ARM boards

Boards running Linux with systemd, 32-bit (ARMv7) or 64-bit.

Linux PC

Any 64-bit PC (x86_64) with systemd: an old laptop will do.

Windows PC

Windows 10 and 11, 64-bit: unzip, run dusty-hub.exe and leave its window open. Or the desktop app in Hub mode.

Raspberry Pi is a trademark of Raspberry Pi Ltd. Dusty is not affiliated with Raspberry Pi Ltd.

Install Dusty Link

Raspberry Pi and Linux PC: a single line

Plug the CNC in over USB, then run this line in a terminal (any Raspberry Pi, another ARM board or a Linux PC with systemd, connected to the Internet). The script picks the right package, checks its SHA-256 sum and installs Dusty Link as a service that starts with the computer. To update it, run the same line again.

curl -fsSL https://dusty.websolutis.com/link/install.sh | sudo sh

Options go after sh -s --: --port /dev/ttyUSB0 (the CNC’s port, otherwise every USB port where a GRBL controller answers), --reseau 192.168.1.50 (CNC over Wi-Fi or Ethernet), --nom Atelier (the name shown to your devices), --virtuelle (the virtual CNC, to try it without a machine).

curl -fsSL https://dusty.websolutis.com/link/install.sh | sudo sh -s -- --port /dev/ttyUSB0 --nom Atelier

Windows 10 and 11

Download the .zip file below and unzip the dusty-link folder, then, in a command prompt: cd dusty-link and dusty-hub.exe --studio studio. Leave the window open: the pairing code is shown there. The USB driver of the CNC (CH340, CP2102) must be installed; allow Dusty Link on the private network if Windows asks.

The pairing code

The pairing code (8 characters) is shown at the end of the installation and stays the same from one start to the next, power cuts included. To see it again: sudo dusty-hub --code. Enter it once on the iPad, the Mac or in the browser to connect.

Direct downloads

SHA-256 checksums. With no Internet on the board: copy its package there, unpack it (tar -xzf), then run sudo ./installer.sh in the dusty-link folder.

Dusty Link and Hub mode, in the manual

Joining the shared machine

  • In a browser: open Dusty Link’s address (http://workshop.local:46590/): Dusty Studio opens, and its Machine tab offers Dusty Link; enter the code, then Connect to Dusty Link.
  • On Mac and iPad: Machine panel › Shared Machine › Dusty Link…: choose a Dusty Link found on the network (or enter its address), then the code.
  • In the desktop app: Machine tab › Dusty Link; Search the Network finds the announced Dusty Links.
  • On a phone: scan the QR code shown by sudo dusty-hub --pendant (or by the apps), or open http://workshop.local:46590/pendant and enter the code.

Safety

Every job start is confirmed on the device that sends it. Disconnecting a device does not touch the machine: a started job goes on, and STOP stays available from every connected device.

In continuous jog on the pendant, the machine moves only while your finger stays on the key; Dusty Link stops it on its own half a second after the last news from the phone.

Questions about Dusty Link

Does Dusty Link cost anything?

No: like Dusty, it is free, with no account.

Do I need Internet in the workshop?

Only to install it with the one-line script. Without Internet on the board, copy its package there and run sudo ./installer.sh. Then everything stays on the local network.

Which machines can it share?

A GRBL 1.1, grblHAL or FluidNC CNC over USB, or a CNC already on the network (--reseau option). The virtual CNC (--virtuelle) lets you try everything without a machine.

How do I find the pairing code again?

sudo dusty-hub --code on the board; it stays the same from one start to the next, power cuts included.

Can several devices be connected at once?

Yes: they all see the machine state and the queue; each job is confirmed on the device that sends it.

Ready to share your CNC?

One line on a Raspberry Pi, and the whole workshop drives the machine.