Skip to content

Dusty Manual

System requirements

The minimum and recommended setup for each platform, the controllers Dusty drives over USB or the network, and what Dusty Link needs to share a machine.

Dusty computes everything on the device (drawing, toolpaths, simulation, G-code): only the anonymous statistics and, in the desktop app, the update check go over the Internet, and both can be turned off. The table gives what the code requires (minimum) and what makes it comfortable to use (recommended).

PlatformMinimumRecommended
MacmacOS 14 Sonoma; Intel or Apple silicon Mac (Metal rendering, available on every Mac that runs macOS 14)Apple silicon Mac (M1 or later), 8 GB of memory, display of 1440 × 900 points or more
iPadiPadOS 17 (every iPad that runs it); the app also installs on iPhone (iOS 17), whose screen is too small to draw comfortablyiPad with an A12 chip or later, keyboard and trackpad for precise drawing; network machine (the iPad has no serial port)
Windows64-bit Windows 10 (x86-64) with WebView2 (built into Windows 11, installed by Windows Update on Windows 10) and a WebGL2 graphics cardWindows 11, processor from 2015 or later, 8 GB of memory, 1920 × 1080 display
Linux64-bit distribution (x86-64) with WebKitGTK 4.1 (Ubuntu 22.04, Debian 12, Fedora 38 or later) and WebGL2Ubuntu 24.04 or equivalent, 8 GB of memory, graphics acceleration enabled
Browser (Dusty Studio)Up-to-date browser with WebAssembly and WebGL2: Chrome, Edge, Firefox or Safari, on a computerUp-to-date Chrome or Edge: WebGPU for drawing and the 3D view, WebSerial to drive the machine over USB
  • Display: the desktop app window is at least 900 × 600 pixels; the inspector needs about 320 points of width next to the canvas.
  • Driven machine: GRBL 1.1, grblHAL or FluidNC controller, over USB (serial port) or the network (Telnet: Mac and iPad app, desktop app). A USB data cable; on Windows, the driver of the board’s USB adapter (CH340, CP210x); on Linux, the right to open the port (dialout group). For other controllers, save the G-code and send it with their own software. Everything can be tried without a machine on the virtual CNC.
  • USB in the browser: WebSerial only exists in Chrome and Edge (and browsers derived from them) on a computer, for a page served over HTTPS. Firefox and Safari draw, compute and save the G-code, but do not drive the machine; no browser opens a network connection to it (see In the browser).
  • Rendering: Metal on Mac and iPad; WebGPU, otherwise WebGL2, in Dusty Studio and the desktop app (WebGL2 on Linux, through WebKitGTK). Without graphics acceleration, software rendering works, slowly.
  • Known measurements (M1 Mac): the 3D view draws 2 million segments in 13 to 15 ms per frame; the machined part of a 21,500-segment job on a 300 × 200 mm stock is computed in 5 to 84 ms depending on the detail, and each frame in 4 to 9 ms; a 500-character text is computed for V-carving in a little over one second. The simulation keeps at most 32 MB of snapshots.
  • Tests: the desktop app was tried on Windows 10 Pro (2013 Core i7 processor, WebGL2) and on Ubuntu 25.04 (WebKitGTK 2.50); the smoothness of the simulation on iPad is not measured yet.
  • Dusty Studio downloads the Dusty core (a few compressed megabytes) on first load, then works offline; its settings and its machine list stay in the browser.
  • Dusty Link (machine shared on the local network): any Raspberry Pi (from the Pi 1 and Zero to the Pi 5) or ARM board under 32- or 64-bit Linux, or a 64-bit Linux PC, with systemd; or 64-bit Windows 10. A few megabytes of memory, the CNC over USB (or the network) and the workshop’s local network; see Dusty Link and Hub mode.

This manual is also built into Dusty: press F1, or open the Help menu, to read the topic for what you are doing. A mistake, a missing answer? Tell us

Try it in Dusty, for free.

Free CNC milling software: design, toolpaths and machine control. Mac, iPad, iPhone, Windows and Linux.