Machining operations
Texturing
Cover a panel or a pocket floor with short ramped strokes drawn at random, for a hammered, gouged or bark-like look that a seed makes repeatable.
A textured background (hammered, gouged or bark-like look) for a panel, a sign or the floor of a pocket: the inside of closed shapes is covered with short ramped strokes laid along parallel lines; each stroke goes in, cuts a bottom, then comes back out. Lengths and depths are drawn at random within the chosen ranges, for a hand-worked look. Closed shapes only; a shape inside another is spared (same rule as the pocket): to texture the background around a motif, assign both the frame and the motif. Tools: ball-nose bit or V-bit (the cut width follows the depth), end mill.
Depths:
- Start depth: the top of the material where the texture goes (0: the surface; the depth of a pocket cut beforehand, to texture its floor).
- Minimum depth and Maximum depth: the bottom of each stroke is drawn between the two, below the start depth; the maximum as a value or a percentage of the stock. Example: start at 3 mm, strokes of 1 to 3 mm → cuts 4 to 6 mm below the surface. A minimum above the maximum is brought down to it (warning).
- Under these fields, Dusty shows the stroke bottoms below the surface, the cut width at the bottom of the shallowest and deepest strokes (from the tool profile) and a side view: two 100 mm sample lines computed exactly like the machining, the material removed and the depth range dotted (enlarged vertical scale), with the number of strokes cut and of pieces skipped.
Lines (“Passes” group):
- Stepover: the spacing between two lines of strokes, as a % of the tool diameter.
- Stepover variance: shifts each line and tilts each of its ends by at most this percentage of a quarter of the stepover: uneven spacing, slightly slanted lines, but never two lines crossing (at 100 %, two lines may touch). Dusty shows the line spacing, at its tightest and widest, and, below, the strokes seen from the top on a sample shape (the outline of each cut, with the operation’s tool).
Strokes (“Strategy” group):
- Raster angle: direction of the lines (0°: along X, 90°: along Y).
- Stock to leave: shrinks the textured area by that much.
- Minimum length and Maximum length: the length of each stroke is drawn between the two.
- Discard below: the edges of the area cut strokes into pieces; a piece shorter than this threshold is not cut: the tool goes up to the fast retraction height and resumes at the next stroke of the same line. 0: lines cut from end to end.
- Line overlap: each stroke starts earlier, above the exit ramp of the previous one (this percentage of that ramp); the tool follows the deeper of the two, so the ridge between two strokes no longer rises all the way up (0 %: it touches the start depth; 100 %: about halfway).
- Offset alternate lines: every other line starts half an average length earlier, the strokes are staggered (clearly visible with two equal lengths).
- Ramp style: Linear, Fall, Arc, Ogee, Smooth, the profiles of fluting, for the entry and, mirrored, the exit of each stroke.
- Ramp share of each line: the share of each stroke’s length taken by its two ramps (100 %: V-shaped stroke, no flat bottom; 0 %: vertical plunge and retract).
- Random seed: every draw (lengths, depths, line placement) depends on it. Same seed, same settings: same texture in the preview, the G-code and on the machine, also after saving and reopening the project. Change it for another texture.
What Dusty does:
- Area: the shapes shrunk by half the width of the deepest cut (plus the stock to leave): the cut never goes past the shapes nor touches a spared motif.
- Order: each part of the area entirely, the nearest first; lines in a zigzag; strokes that follow each other are cut in one go, without lifting.
- Feeds: descents at the ramp rate, bottoms and climbs at the cutting feed, vertical moves at the plunge rate.
- Strokes deeper than the profiled part of the tool (cone height, ball radius) are reported: beyond it, the width no longer grows.
Tip: with a 6 mm ball-nose bit, strokes of 6 to 14 mm cut 0.5 to 2 mm deep, a 40 to 50 % stepover and an arc ramp over half the stroke give an even hammered background; check the result in the preview (simulated workpiece) before machining.
Differences from MillMage: the seed is a setting of the operation (the reference software says nothing about it); the overlap is measured as a share of the exit ramp and the stepover variance never crosses two lines (formulas of Dusty’s own, the reference software only giving the names of the settings).
This manual is also built into Dusty: press F1, or open the Help menu, to read the topic for what you are doing. A mistake, a missing answer? Tell us
Try it in Dusty, for free.
Free CNC milling software: design, toolpaths and machine control. Mac, iPad, iPhone, Windows and Linux.