Skip to content

Machining operations

3D relief roughing

Clear the bulk of the material above a depth map, level by level, with a large tool, leaving a skin for finishing: with or without a carved background.

Relief roughing removes, level by level, the bulk of the material above a depth map, with a fairly large tool, leaving a skin for finishing (relief finishing is not available yet). The map follows the gray convention: white = the start depth, black = the final depth; the thickness of the relief is their difference.

Assigning the operation:

  • Map only (relief with carved background): select the map, then New Operation › 3D relief roughing. The machined area is the map’s frame (its mask if it has one): the black background around the relief is carved to the final depth, up to a straight wall at the edge of the frame.
  • Map and a closed shape (relief without carved background): select the map and its outline (made by Generate Outline on insertion; one click on the group takes both) or any closed shape around it. Only the inside of the shape is machined; inside the shape but outside the map, the background is black (carved to the final depth). Open shapes are ignored (reported).
  • The tool stays entirely inside the area: nothing around is touched, even with a large tool (so it does not go down against the edge of the area: that is the skin left at the edge).
  • Tools: end mill (corner radius included), ball nose, V-bit (tip flat included).

Settings:

  • Start depth (the white; 0: the stock surface) and Final depth (the black), as a value or a percentage of the stock. The material above the white is removed as well.
  • Depth per pass: the height of the levels, counted from the stock surface.
  • Clearing pattern: Raster (parallel back-and-forth lines; Raster angle: 0° along X, 90° along Y) or Offset (from the center out to the edge; Cut direction climb or conventional). No outline pass. A thumbnail shows the pattern.
  • Stepover: the distance between two lines or two loops, in % of the tool diameter.
  • Depth to leave: the skin kept for finishing, the same in every direction: on top, on the flanks of the relief and against the edge of the area.
  • Slow down the first loop and First loop feed rate (offset only): the first loop of each level, which attacks the material over the full width of the tool, at this percentage of the feed; then the full feed.

What Dusty does:

  • Map: the grays of the PNG, 8 or 16 bits, ignoring its transparency (a transparent background stays the most carved). The image adjustments (brightness, contrast, gamma, enhancement) do not count: machining follows the grays of the file (reported if they are not neutral). A JPEG map or any format other than PNG is refused.
  • Never into the relief: on a fine grid (an eighth of the tool radius, four million cells at most), Dusty computes the lowest height the tip can take so that the tool, with its exact shape and grown by the depth to leave, touches the relief nowhere, with a margin for every position between two grid points. The skin is therefore never thinner than asked; it can be a little thicker in narrow hollows and at the foot of steep slopes.
  • Levels: the same pattern is followed at each level, one depth per pass lower, and laid on the relief where it is higher: under the tool, never more than one depth per pass is removed at once. What has nothing left to remove is followed in the air when short, otherwise flown over rapidly just above what is already machined along the path.
  • Moves: plunge entry; the rapid descent stops at the pocket lift clearance above what the tool has already machined at the same place; between two chains of the pattern and between two levels, rapid retract above the stock. No rapid move goes through the material (the pre-send check verifies it).
  • Feeds: cutting feed along the relief, reduced on the way down so as never to exceed the plunge feed in Z.
  • Limits: maps of 6,000 pixels per side and 36 million pixels at most; a toolpath of more than a million moves is refused with a message telling what to change (depth per pass, stepover, smaller area).
  • The toolpath is made of lines (no fitted arcs: an arc would stray from a path that hugs the relief).

Tip: rough with a 6 mm end mill or ball nose, levels of 2 to 3 mm, a 40 % stepover, 0.5 mm to leave; check the result in the preview (simulated workpiece) before machining. A square-meter relief with a 3 mm tool takes hundreds of thousands of moves: machine it piece by piece (one closed shape per piece).

Saving

The operation and its settings are kept in the .dusty, with the map and its link to the model. Earlier versions: version 1.1.1 and the 1.2.0 of the previous lots open such a project without a message; they keep the operation but do not machine it: the G-code is refused (“This version does not compute 3d relief roughing toolpaths yet”), nothing is machined silently. Saved again by them, the project keeps the operation and its settings (1.1.1 loses the link from the map to its model): reopened here, it is machined as before.

Differences from MillMage: the tool stays inside the area (MillMage lets its center go to the edge and warns that a large tool may cut beyond the shapes); the depth to leave is a uniform skin (MillMage speaks of shrinking the area, without more detail); entry is a plunge (MillMage also offers the zig-zag ramp and the spiral); the map must be a PNG and the image adjustments do not count.

This manual is also built into Dusty: press F1, or open the Help menu, to read the topic for what you are doing. A mistake, a missing answer? Tell us

Try it in Dusty, for free.

Free CNC milling software: design, toolpaths and machine control. Mac, iPad, iPhone, Windows and Linux.