Skip to content

Preview

Machined part

Dusty carves the stock with the real shape of each tool and follows the time slider: colors by depth or operation, wood and metal textures, detail and hidden pieces.

In the Display section, the 3D View setting offers Toolpaths (the paths as wireframe), Machined Part (the stock as machining leaves it) or Part and Toolpaths: the part on the left, the toolpaths on the right (one above the other on a narrow screen), seen from the same angle — rotating, panning or zooming one does the same to the other.

Dusty simulates the part: each tool move carves the stock with the real shape of the operation’s tool — flat bottom of the end mill, rounded corner of an end mill with a corner radius (bull nose), round tip of the ball mill, cone of the V-bit, the scribe and the drill, and the concave profile of the round-over bit (its radius and tip length, like the tool’s outline): the edge it follows comes out rounded. The project’s stock and Z zero are respected; what is cut through shows the table, and tabs remain. The part follows the slider and playback: move the slider back and the material comes back; play the job and watch the tool carve.

Settings of the Machined Part section:

  • Toolpaths on the part: none, the last 100, 1,000 or 10,000 segments already machined, or all. They are drawn in front of the surface they carved.
  • Colors: Material (the stock color everywhere; the shape reads through lighting), Depth (the toolpath gradient, from gold to purple) or Operation (each operation’s paint color: you see which one machined what). Untouched stock keeps its color.
  • Texture: the look of the stock, drawn by Dusty (nothing is downloaded) — Stock color (the brand color, by default), about fifteen woods (oak, walnut, maple, pine, birch…, MDF, plywood with its plies on the sides), painted wood in thirteen colors (paint on top, wood where the tool went), metals (brushed aluminum, brass, copper), ten solid colors and a few miscellaneous patterns (concrete, cheese, leopard fur, fur, ice cream, foam). The pattern follows the material through its thickness: machined sides and floors show the heart of the wood. With the Depth or Operation colors, only untouched stock takes the texture. The choice is kept from one opening to the next.
  • Detail: Low, Normal, High or Fine — one point of the part every 0.5, 0.25, 0.125 or 0.0625 mm at best. On a large stock, Dusty widens this step to keep memory and computing bounded (from 2 MB at low detail to 24 MB at fine detail, plus the snapshots that make going back instant). Lower the detail for a very large stock or a modest device, raise it for fine engravings.

Good to know:

  • The part is computed when it is shown and whenever the detail changes; on a very large job, it catches up with the slider in a few frames.
  • The simulation follows a 3-axis machine, the tool carving from above: no undercuts.
  • Rapids carve too: a rapid through the material shows on the part (the pre-send check reports it).
  • Hidden pieces: a cut all the way through splits the part into pieces (the frame around a cut-out part, the slug of a hole). Double-click (iPad: double-tap) a piece to hide it and see the rest better; a piece still held by tabs cannot be hidden (the double-click reframes then, as elsewhere). Show Hidden Pieces brings them back, as does opening the preview again or changing the detail. The mask applies from the moment of the cut: moving the slider back before it brings the piece back.
  • VoiceOver describes the part: view, moment shown, depth reached, share of the surface machined, cut through, hidden pieces, detail.

In Dusty Studio and the desktop app, the preview is the same: Top, 3D or Both layout (at the top; Both at the first opening, then the last choice), Tool at Cursor, Display (choosing a 3D content from the top view alone shows the 3D area) and Machined Part (texture included) sections, preset views, zoom and reframing, 3D Check and Troubleshooting sections. Drag to rotate, Shift + drag (or right button) to pan, wheel to zoom, double-click to reframe (or hide a cut-out piece of the machined part); on the keyboard, arrows, + and −, 0.

This manual is also built into Dusty: press F1, or open the Help menu, to read the topic for what you are doing. A mistake, a missing answer? Tell us

Try it in Dusty, for free.

Free CNC milling software: design, toolpaths and machine control. Mac, iPad, iPhone, Windows and Linux.